Morsecove

A message, a pattern, a little mystery.

Morse Code Necklace

Turn a name, date or dedication into a strand of round and tube beads. Size the pattern, then save it for your maker.

Bead strand preview

A round bead is a dot and a tube bead is a dash.

Your message stays in this browser. The designer works without an account and never uploads or stores your input.

Choose the part of the story that goes on the chain

A Morse code necklace gives you a strip of space across the collarbone. A name like MAY can sit between two short lengths of plain chain. A phrase like I LOVE YOU needs room for three words and two visible breaks. Start with the version you want to wear, say it aloud, then use the Morse code translator to hear where each letter ends. For a dedication, try the Morse love note before committing it to beads.

A date needs a reading order. Write 24 DEC if the day and month matter more than the year. For coordinates, keep the direction letters, as in 51 N 1 W, and choose the precision deliberately. Each digit adds five beads. The Morse code numbers page lets you check the digits individually before you ask someone to string them.

Match each bead to its place on the chain

Read the preview from left to right. A round bead marks a dot. A tube marks a dash and takes three times the round bead’s width along the chain. If your round beads measure 2 mm, look for tubes close to 6 mm long. At a 1 mm spacing setting, leave 1 mm between signals in a letter, 3 mm between letters and 7 mm between words. The gaps replace one another at boundaries.

Ask how the maker holds those spaces in place. Beads that slide freely can bunch at the lowest point and erase a word break. Crimps, fixed stations or spacer tubes can hold the pattern. Check that the chain passes through the bead holes, and specify which end carries the first letter when the necklace is worn. Compare each group against the Morse code alphabet.

Work out how much chain the message needs

Count one bead for every dot or dash and none for a space. With 2 mm dots, 6 mm dashes and the 1 mm spacing setting, the examples below give the width of the message alone. A full necklace also needs plain chain around the neck, plus the clasp and any extender.

Cut a paper strip to the calculated length and drape it at your usual neckline. If the wording disappears around the sides, try initials or split the dedication between a necklace and a matching Morse bracelet.

What to ask before choosing a finished necklace

On a maker marketplace such as Etsy, in an Amazon listing or at a local custom shop, look for a close-up beside a ruler. Ask for the bead dimensions, base metal, finish and overall chain length. A silver-colored preview can represent sterling silver, plated brass or steel. Request the actual material description for the beads and the clasp.

Send the PNG with the intended spelling and ask for a laid-flat photo before assembly. Someone glancing at the necklace may see a decorative sequence. Someone who knows Morse can read it if the direction and gaps are clear. To compare the same message as marks on a line, open the Morse tattoo stencil.

FIELD NOTES

Questions about your necklace

How much of a sentence will fit across the front of a necklace?

Measure the front span on a necklace you wear and compare it with the message length shown here. At 2 mm bead diameter and 1 mm spacing, I LOVE YOU spans 141 mm. Changing the wording, bead size or spacing changes that figure.

How can I tell a dot bead from a dash bead?

Look along the chain rather than across it. The round dot is one bead diameter long and the dash tube is three diameters long in this preview. Check both lengths against the maker’s ruler photo.

Can someone recognize the message while I am wearing it?

The sequence may look like a decorative pattern at a glance. A reader familiar with Morse can work it out when the first letter, direction and letter gaps are identifiable. Avoid putting a secret or an exact private address on a visible necklace.

Does the silver finish mean the necklace is sterling silver?

The silver, gold and dark options change the appearance of the drawing. Ask the maker for the base metal, any plating and the material of the clasp before choosing an actual necklace.

Can a Chinese name or an emoji go on the bead chain?

For a Chinese name, enter the Latin-letter spelling that you want the recipient to read. Replace an emoji with a short word. The editor flags unsupported characters so a maker can see exactly what the exported pattern represents.

Why might a finished necklace differ from my PNG?

The PNG lays the beads flat and uses their nominal dimensions. Chain curvature, hole placement, spacers and bead tolerances can change the drape. Ask the maker for a measured proof of the beaded section and the full necklace length.