Morsecove.THE PRIVATE SIGNAL ROOM

A message, a pattern, a little mystery.

FIELD NOTE / 03THE SIGNAL ROOM

SOS in Morse code

Three short. Three long. Three short. Hear the continuous SOS signal and practise its rhythm.

01 / SIGNAL PRACTICE600 Hz · PLAYS ONCE
SOS

One continuous signal. These visual groups do not add letter pauses.

0.00 / 2.30 s
Speed · WPM

Ready. Three short, three long, three short.

...---...
Practice a phrase
Optional light demonstration

The small lamp will flash with the sound. Flashing can be uncomfortable for some people. Enable it only if you want to view flashing light.

Practice tool only. This page does not contact emergency services.

What is SOS in Morse code?

SOS is ...---...: three short elements, three long elements, then three short elements. The whole pattern is one continuous signal. The familiar letters are a convenient way to remember it, but the signal does not include the longer pauses that would normally separate S, O, and S in a written message. The International Telecommunication Union describes this distinction in its account of the SOS signal.

The three groups above make the pattern easy to see. They do not create three separate pieces of audio. Listen for a single phrase with a longer middle: short, short, short; long, long, long; short, short, short. The sound ends after one complete pass, so you can listen, pause, and reproduce the rhythm before playing it again.

Hear the rhythm, then count the gaps

A dot takes one time unit and a dash takes three. The quiet interval between neighbouring elements takes one unit. Ordinary Morse text uses three units between letters and seven between words. These proportions are set out in ITU-R M.1677-1, section 2. This practice player applies those ratios consistently to the sound and its progress display.

At the default setting of 12 WPM, one unit in this player is 0.1 seconds. Each dot lasts 0.1 seconds, each dash lasts 0.3 seconds, and each internal silence lasts 0.1 seconds. There are six dots, three dashes, and eight internal gaps: 23 units altogether. The complete SOS demonstration therefore lasts 2.3 seconds, measured from the first tone to the end of the last one.

Part of the signalLengthAt 12 WPM
One dot1 unit0.1 seconds
One dash3 units0.3 seconds
Gap inside SOS1 unit0.1 seconds
Whole SOS signal23 units2.3 seconds

Change the speed to 8 WPM if you want more time to follow individual elements. At 20 WPM, listen for the overall shape instead of counting each mark. Speed changes shorten or lengthen every part together; they never turn a dash into a dot or insert an extra pause between the visual groups. The displayed duration updates before you play.

A short listening and tapping exercise

  1. Listen once without tapping. Notice where the three longer tones begin and end. Keep your attention on the whole pattern rather than trying to translate the three letters.
  2. Repeat it with a held motion. Press a finger gently against a surface for each sound and lift it during each silence. Hold each long element about three times as long as a short one. This makes duration easier to practise than a quick tap that ends immediately.
  3. Compare with another playback. Check whether the long middle elements became too short, or whether you added a large pause before or after them. Correct one part at a time.
  4. Try a different speed. Keep the same proportions while changing the overall pace. Return to 12 WPM to check that the rhythm still feels familiar.

For a quiet practice session, use the printed pattern and count the lengths yourself. A single tap has very little sustained duration, so it can hide the difference between a short element and a long one. Holding a key, making a continuous vocal sound, or tracing a mark with your finger gives you a clearer way to represent that difference. These are learning exercises for timing; the page is not a communications system.

Watch a small light demonstration

Sound playback leaves the lamp off. A thin mark indicator and the progress bar show where you are in the sequence without flashing the whole tool. If you want to compare light with sound, open Optional light demonstration, read the flashing notice, and select Allow a flashing light. Then choose Play light demo. Enabling the checkbox alone does not start anything.

The small lamp follows the same timeline as the tones: on for each element, off for each gap. It stays within the green signal panel and ends after one pass. Stop ends the demonstration immediately, and unchecking the option also stops active light playback. Leaving the page or switching to another browser tab stops the current playback. You can keep the light option off throughout your practice and use the sound or printed pattern instead.

Compare SOS with HELP and NEED HELP

The phrase buttons demonstrate a useful difference between a continuous signal and ordinary text. HELP is four letters, so its playback includes a full letter gap after H, E, and L. NEED HELP also includes a word gap. The slash in its written code represents that word boundary; it is not a sound to play.

SelectionWritten codeWhat to notice
SOS signal...---...Only short internal gaps
HELP.... . .-.. .--.Clear separation between letters
NEED HELP-. . . -.. / .... . .-.. .--.A longer gap between the two words

Choose a phrase before pressing Play sound. Changing a selection stops the current sequence and updates the code, diagram, and total duration. Copy code copies the selected pattern as plain text. Choose SOS signal to return to the original continuous example. For other messages, use the Morse code translator; for a character you want to study in isolation, open the Morse alphabet.

Check these common practice mistakes

Adding letter gaps to SOS: the large visual spaces are for reading. Listen to the one-unit silences between all nine elements, including the transitions from short to long and long to short. Making every element the same length: focus on sustaining the middle three elements. Rushing the final dots: let the last three short elements match the first three.

Reading the graphic as an exact scale drawing: the shapes help identify dots and dashes, while the sound is what demonstrates their durations. Expecting automatic repetition: this tool plays once by design. Repeat manually when ready so there is time to compare your attempt. Expecting a message to be sent: all playback is a local browser demonstration. Practice tool only. This page does not contact emergency services.

FIELD NOTES

SOS, explained

What is SOS in Morse code?

SOS is ...---...: three short elements, three long elements, and three short elements. It is played as one continuous nine-element signal, with short internal gaps and no added letter gaps.

Do you pause between the S, O, and S?

Do not add normal letter pauses when practising the SOS signal. Each neighbouring element is separated by one dot-length gap. The three visual groups on this page are a reading aid, not three separately spaced letters.

How long does the SOS sound last?

In this player, SOS lasts 2.3 seconds at the default 12 WPM. Its six dots, three dashes, and eight internal gaps add up to 23 time units. Changing the speed scales every part of the signal together.

How can I practise SOS with tapping or light?

For a timing exercise, hold each short action for one count and each long action for three, with one count between neighbouring actions. The optional light demonstration follows the audio timeline in a small lamp. Read the flashing notice and explicitly enable it before playing.

Is HELP the same Morse pattern as SOS?

No. HELP uses the code “.... . .-.. .--.” with normal letter spacing. SOS uses “...---...” as one continuous signal. The phrase buttons let you hear the difference, and NEED HELP adds a seven-unit word gap.

Does this page send an SOS or contact emergency services?

No. This is a browser practice tool. Play sound and Play light demo produce local demonstrations only. Nothing is transmitted to an emergency service, and each demonstration stops after a single pass.