Morsecove

A message, a pattern, a little mystery.

Morse Code Decoder

Paste written Morse to read the text. For audio, transcribe the rhythm by ear using the guide below.

Field guide

Paste a message and check its boundaries

Paste the full line into the input field, including any slashes. Read the decoded text alongside it. Try .... .. / - .... . .-. . first. You should see HI THERE, with the word break in the same place as the slash. If the letters look right but two words have run together, inspect the separator between those words before changing any dots or dashes.

The morse code translator is handy for a quick trip in either direction. Use this page when you need to work out why a received message reads a certain way. It accepts written signals, including a transcription you make while listening to audio. For a recording, first write down the short sounds, long sounds, and pauses you can hear. There is no recording upload or microphone input on this page.

Keep sound timing separate from keyboard spaces

A dot sets the unit of time. A dash lasts three units. Within a character, adjacent marks have one unit of silence between them. Two complete characters have three units of silence between them, and two words have seven. Those are total gaps. You do not add a character gap on top of a word gap. These proportions are defined in the international Morse code recommendation.

On a keyboard, keep the marks belonging to one character together. One or two typed spaces start the next character. A slash, a line break, or at least three spaces start the next word. For text you plan to share, use one space between letters and a slash between words. Messaging apps sometimes collapse repeated spaces, and a slash survives that change. A slash represents a pause in this notation. To send the actual punctuation character in a fraction, use its group of marks, -..-..

This difference explains a surprisingly common puzzle. The single group .- is A. If someone presses the space bar between the same two marks, . - becomes E followed by T. Both inputs are valid and neither produces an error. When the output contains recognizable letters but the message makes little sense, changing a boundary may explain more than changing a mark. Use the playable alphabet to compare the two rhythms.

Four examples you can copy

Paste this line Expected text What to listen or look for
.... .. / - .... . .-. . HI THERE A word boundary after the first two characters
.--. .. . .-. / ..--- PIER 2 A five-mark digit after a word
...-- -..-. ....- 3/4 The slash is encoded punctuation inside the fraction
--. --- ..--.. GO? The final group is the question mark itself

Try changing just one part of a known example. In the second line, remove the slash and leave one space before the digit. PIER2 is a different result, though the digit itself is unchanged. In the third line, replace the middle group with a literal slash to get two separate numbers. These tests locate the role of a separator without asking you to remember a whole table of punctuation.

Recover a message with missing spaces

Start by keeping a copy of the original. Mark any word gaps you can identify from the source. Within one small section, write down two possible divisions and decode them separately. For instance, ... could be S, .. . could be IE, and . . . could be EEE. All three use the same marks in the same order. A decoder that receives only the unspaced marks has no evidence for choosing the word the sender meant.

Use what you know about the message to test a proposed division. If the sender promised a four-digit locker number using full international digits, expect four groups of five marks. If the marks do not divide that way, check for a dropped mark before trying to turn the sequence into a name. A call sign or a puzzle answer may offer clues about the expected mix of letters and numbers, but a plausible reading is still a guess. Ask for the original spacing when the exact wording matters.

Read an unknown group without losing your place

An unrecognized group produces a question mark in the output and an input warning that identifies the problem. Copy that group aside. Count its marks, compare the original punctuation, and check whether two neighboring letters lost their space. For instance, eight dashes cannot be one ordinary digit. Silently dropping three dashes to make a zero would change the message. Leave a visible uncertainty in your notes until the source supports a correction.

A decoded question mark can also be genuine punctuation. In the GO example above, the last group is a supported question mark and the input stays valid. Compare the warning with the result before assuming a character is damaged. The field also accepts some typographic variants of dots and dashes. Start with plain periods and hyphens if you are transcribing by hand so you can compare your copy with the source a mark at a time.

Transcribe a short recording by ear

Listen to a few seconds at a time. On the first pass, mark the longest pauses between words. On the next, insert a space wherever one character ends. Only then fill in the dots and dashes inside each character. If the playback software lets you slow the recording evenly, the ratios between marks and gaps should remain useful. Background clicks can resemble very short signals, so replay any group that changes the sense of an otherwise clear sentence. Paste the transcription here and compare the result with your notes before moving on.

FIELD NOTES

Common questions

Can I paste a whole paragraph with slashes?

Yes. Paste the marks and separators together, up to 1,000 characters. A slash or a line break starts a new word.

Can the decoder identify letters with no spaces?

It reads a continuous group as one character. Several divisions can fit the same marks. Recover the boundaries from the original timing or the sender.

Does this decoder accept an audio upload?

It accepts a written transcription. Listen for the marks and pauses, write them as dots, dashes, spaces and slashes, then paste the line.

Why does a question mark appear in my answer?

Check the input warning. An unknown group gets a placeholder. The valid group ..--.. decodes to an actual question mark without that warning.